Volkswagen Golf MK7 (5G) coding mods

Volkswagen Golf MK7 (5G) mods

Coding mods, retrofit guides, service & repair procedures.
Selected with specially for your Volkswagen Golf MK7 (5G).
Enable hidden options, adjust factory features, tweak your ride, fix fault codes.
Make your car fit your individual needs.

Mods, retrofits, service procedures:

ACC Radar Misalignment fix (fault C1103)

ACC/Front Assist radar calibration procedure required after removing front bumper, modifying suspension, or frontal collision.
Connect with radar and confirm that there's C1103 00 - Adaptive Cruise Control Sensor - misadjusted fault stored.
Module: 13 (ACC radar)
Faults → Read
Check current misalignment angle.
Module: 13 (ACC radar)
Live Data → misalignment angle
Perfect setting is 0.00. Tolerance is between -0.80 and 0.80 degree. Values below -0.80 mean radar is facing too much to the right. Values above 0.80 mean radar is facing too much to the left. One turn of the adjustment screw equals to 1 degree.
Remove cover from the radar head. Use adjustment screws to change radar position. Put the cover back on.
Module: 13 (ACC radar)
Security Access → Code: 14117
Module: 13 (ACC radar)
Basic Settings → Reset misalignment angle for sensors → Go
Module: 13 (ACC radar)
Faults → Clear
Perform test drive at least 10km long. Check live data and repeat the procedure if required.
Procedure ID: 200

Adaptive Cruise Control 1km/h Precision activation

Change setting to 1mph or 1km/h increments by short press of the ACC buttons, use the old 5mph or 10km/h speed increments with press and hold of the buttons.
Watch Adaptive Cruise Control 1km/h Precision activation tutorial on YouTube.
Module: 13 (ACC radar)
Security Access → Code: 14117
Module: 13 (ACC radar)
Coding → Long Coding → Byte: 02 → Bit: 6
New value: enable
Procedure ID: 191

Adaptive Lane Assist activation

This option will force Lane Assist to keep your car in the middle of the lane, instead of late intervention when the car drifts to the side. Additionally you will have option to adjust it from the infotainment screen.
Watch Adaptive Lane Assist activation tutorial on YouTube.
Module: A5 (Front Sensors Driver Assistance System)
Security Access → Code: 20103
Module: A5 (Front Sensors Driver Assistance System)
Adaptation → Channel: Intervention moment
New value: early (setting via menu)
Procedure ID: 169

Auto Hold Memory Setting activation

Automatic parking brake memory settings. Auto Hold function can be remember last state or by default be at start of journey on or off.
Watch Auto Hold Memory Setting activation tutorial on YouTube.
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 28 → Bit: 4
New value: enable
Procedure ID: 155

Brake Drying System adjustment

System that is applying brake pads to the brake discs, to keep you brakes dry when raining.
Module: 03 (ABS brakes)
Adaptation → Channel: Disc Drying
New value: Weak / Normal / Hard
Procedure ID: 36

Central Lock Acoustic Confirmation when Locking activation

Enables sound confirmation when locking and unlocking car, as well as option to control this feature from the multimedia system menu.
Watch Central Lock Acoustic Confirmation when Locking activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung Entriegeln
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung Verriegeln
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Acknowledgement signals - Dauer der Akustischen Rueckmeldung vom Einfachhorn
New value: Kurz
Module: 09 (Central Electronics)
Adaptation → Channel: Acknowledgement signals - Akustische Rueckmeldung global
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Acknowledgement signals - Menuesteuerung akustische Rueckmeldung
New value: active
On the infotainment display go to Car → Setup → Lock & unlock and enable "Acoustic confirmation" option.
Procedure ID: 135

Central Lock Automatic Unlocking when Gearbox in P activation

Door locks will automatically unlock when automatic transmission is shifted in to Park position.
Watch Central Lock Automatic Unlocking when Gearbox in P activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control - Autounlock NAR
New value: active
Procedure ID: 170

Central Lock Hatch Pop with Remote Control

Press and hold trunk button on the remote control to pop the lock.
Watch Central Lock Hatch Pop with Remote Control tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control - Direkter Auswurf des Heckdeckels
New value: active
Procedure ID: 171

Central Lock Trunk Delay activation

Keeps your trunk lock open for another 20-30 seconds after you open it with the remove and close it to give you chance of recovering keys from the car.
Watch Central Lock Trunk Delay activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control - Freigabenachlauf Heck nach Einzeloeffnung ueber HDF-Funktaster
New value: active
Procedure ID: 194

Climatronic Fan Speed Display on with Auto Mode activation

Shows current blower fan speed when Climatronic auto mode is enabled.
Watch Climatronic Fan Speed Display on with Auto Mode activation tutorial on YouTube.
Module: 08 (Automatic heat, ventilation, air condition)
Coding → Long Coding → Byte: 11 → Bit: 6
New value: enabled
Procedure ID: 70

Climatronic Fan Speed Profiles activation

Shows adjustment of the fan speed profile when Climatronic auto mode is enabled.
Watch Climatronic Fan Speed Profiles activation tutorial on YouTube.
Module: 08 (Automatic heat, ventilation, air condition)
Coding → Long Coding → Byte: 07 → Bit: 0
New value: enable
Procedure ID: 176

Comfort Turn Signals activation and adjustment

Changes how many times should the indicator blink when using comfort indicators.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Turn signal control-Komfortblinken
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Turn signal control-Komfortblinken Blinkzyklen
New value: from 2 to 5
For the changes to be applied it's required to reset light settings to factory defaults from the infotainment display menu.
Procedure ID: 130

Coming/Leaving Home Lights Automatic activation

Enables automatic Leaving Home lights when the ignition is turned on. By default control unit is set to "manual", which requires driver to pull the high beam stalk after turning the ignition off.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Comfort Illumination - Coming Home Verbaustatus
New value: automatic
Procedure ID: 143

Coming/Leaving Home Lights via Fog Lights activation

Front fog lights will be used as welcome lights instead of the low beam.
Watch Coming/Leaving Home Lights via Fog Lights activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Comfort Illumination - Coming Home Lights
New value: Nebellicht
Procedure ID: 126

Cornering Lights Speed Threshold adjustment

Adjust speed range in which cornering lights are activated.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Static cornering light lower speed threshold
New value: 0
Module: 09 (Central Electronics)
Adaptation → Channel: Static cornering light upper speed threshold
New value: 50
Procedure ID: 34

Cornering Lights via Fog Lights activation

Front fog lights will be used as cornering lights.
Watch Cornering Lights via Fog Lights activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Lichtfunktion B12 auswählen
New value: Abbiegelicht links
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Lichtfunktion B13 auswählen
New value: Abbiegelicht rechts
Procedure ID: 33

DRLs Off with Handbrake On activation

Daytime running lights will automatically turn off when parking brake is engaged.
Watch DRLs Off with Handbrake On activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Daytime running lights-Tagfahrlicht Dauerfahrlicht bei Handbremse abschalten
New value: active
Procedure ID: 109

DRLs Option on Infotainment Display activation

Enables option to turn on and off daytime running lights function from the Car → Setup → Lights menu.
Watch DRLs Option on Infotainment Display activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Daytime Running Lights activation by BAP or Operating sequence possible
New value: active
Procedure ID: 128

DRLs via Fog Lights activation

Front fog lights will be used as daytime running lights.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Lichtfunktion B12 auswählen
New value: Daytime running lights
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Lichtfunktion B13 auswählen
New value: Daytime running lights
Procedure ID: 124

DRLs with Rear Lights On activation

Turn on tail lights when Daytime Running Lights are on.
Watch DRLs with Rear Lights On activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Daytime running lights-Tagfahrlicht-Dauerfahrlicht aktiviert zusartzlich Standlicht
New value: active
Procedure ID: 121

Door Ambient Lights with Brightness Control retrofit

Enable door ambient illumination that will turn on with courtesy lights when you open the door, and will stay on dimmed when doors are closed. In car setup on the infotainment display you can adjust brightness of the ambient illumination.
Requires connecting positive wires to door control modules (32-pin socket; pin 3 and pin 8) and negative to chassis ground.
Module: 5F (Information electronics)
Adaptation → Channel: Car_Function_List_BAP - interieur_light_0x08
New value: activated
Module: 5F (Information electronics)
Adaptation → Channel: Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination
New value: activated
Module: 5F (Information electronics)
Adaptation → Channel: Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination_over_threshold_high
New value: activated
Module: 42 (Driver door electronics)
Coding → Long Coding → Byte: 01 → Bit: 1
New value: enable
Module: 42 (Driver door electronics)
Coding → Long Coding → Byte: 01 → Bit: 3
New value: enable
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 01 → Bit: 1
New value: enable
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 01 → Bit: 3
New value: enable
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 17 → Bit: 1
New value: enable
Module: 09 (Central Electronics)
Adaptation → Channel: Interior light; light configuration - Ambiente_Applikationsleisten_in_Tuertafel
New value: installed
Module: 09 (Central Electronics)
Adaptation → Channel: Interior light; Ambient lighting - Defaultwert Ambienteprofil Tuer
New value: 50%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting: parameter - p_adaption_kundenwunsch_tuer
New value: 3C
Procedure ID: 175

Door Warning Lights retrofit

Enable warning lights that will turn on when you open the door.
Requires connecting positive wire to door control modules (32-pin socket; pin 16) and negative to chassis ground.
Module: 42 (Driver door electronics)
Coding → Long Coding → Byte: 01 → Bit: 2
New value: enable
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 01 → Bit: 2
New value: enable
Procedure ID: 174

ESC Settings with ESC Modes activation

Enables ESC options to be set from the headunit with modes: "Active", "ESC sport", "ESC off".
Watch ESC Settings with ESC Modes activation tutorial on YouTube.
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 0
New value: disable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 1
New value: enable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 2
New value: enable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 3
New value: disable
Procedure ID: 148

ESC Settings with GTI/R Modes activation

Enables ESC options to be set from the headunit with modes: "Active", "ASR off", "ESC sport".
Watch ESC Settings with GTI/R Modes activation tutorial on YouTube.
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 0
New value: enable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 1
New value: disable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 2
New value: disable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 3
New value: enable
Procedure ID: 32

ESC Settings with OFF Modes activation

Enables ESC options to be set from the headunit with modes: "Active", "ASR off", "ESC off".
Watch ESC Settings with OFF Modes activation tutorial on YouTube.
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 0
New value: enable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 1
New value: disable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 2
New value: enable
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 29 → Bit: 3
New value: disable
Procedure ID: 149

Emergency Brake Lights and Hazard Lights activation

Flashing brake lights when emergency braking from speeds above 50mph (80km/h) and hazard lights when emergency stopping.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Dyn. turn signal modes - Emergency alert blinken
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Dyn. turn signal modes - Notwarn blinken NBA Phase 2
New value: active
Procedure ID: 162

Engine Idle Speed adjustment

Increase engine idle speed by a correction value for smoother engine operation while idling.
Watch Engine Idle Speed adjustment tutorial on YouTube.
Module: 01 (Engine Electronics)
Security Access → Code: 27971
Module: 01 (Engine Electronics)
Adaptation → Channel: Idle RPM correction
New value: 100
Procedure ID: 193

Flash To Pass Lights via Fog Lights activation

Front fog lights will be used as additional flash to pass lights when left stalk is pulled towards.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Lichtfunktion D 12
New value: Lichthupe generell
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Dimmwert CD 12
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Dimming Direction CD 12
New value: Maximize
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Lichtfunktion D 13
New value: Lichthupe generell
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Dimmwert CD 13
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Dimming Direction CD 13
New value: Maximize
Procedure ID: 157

Footwell Lights with Ambient Backlight Control retrofit

Enable footwell lights that will turn on with courtesy lights when you open the door, and will stay on dimmed when doors are closed and headlights are on. In car setup on the infotainment display you can adjust brightness of the background illumination.
Get VAG LED Footwell lights on Ali4Cars.com
Requires connecting positive wire to BCM (socket C; pin 72) and negative to chassis ground.
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 05 → Bit: 7
New value: enable
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 17 → Bit: 3
New value: enable
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte30FR LC72 - Lasttyp 30
New value: 36-LED Kleinleistung
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte30FR LC72 - Fehlerort mittleres Byte DTC-DFCC 30
New value: 02
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte30FR LC72 - Lichtfunktion A 30
New value: Fussraumlicht
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte30FR LC72 - Dimmwert AB 30
New value: 100
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte30FR LC72 - Lichtansteuerung HD AB 30
New value: always
Module: 09 (Central Electronics)
Adaptation → Channel: Ambient lighting - Defaultwert Ambienteprofil Fussraum
New value: 100%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior light; light configuration - Fussraumbeleuchtung
New value: installed
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_adaption_kundenwunsch_fussraum
New value: 14
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_max_fussraum
New value: 100%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_HD_auf_zuendung_ein_fussraum
New value: 126%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_HD_auf_zuendung_aus_fussraum
New value: 127%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_dieseTuer_auf_zuendung_ein_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_andereTuer_auf_zuendung_ein_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Fzg_geschlossen_zuendung_ein_fussraum
New value: 126%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_dieseTuer_auf_zuendung_aus_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_andereTuer_auf_zuendung_aus_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_einausstieg_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Fzg_geschlossen_zuendung_aus_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Tueren_geschlossen_HD_auf_zuendung_aus_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Tueren_geschlossen_HD_zu_zuendung_aus_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Tueren_geschlossen_schluessel_ab_fussraum
New value: 70%
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting; parameter - p_helligkeit_Fzg_geschlossen_schluessel_ab_fussraum
New value: 70%
Module: 5F (Information electronics)
Adaptation → Channel: Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination
New value: activated
Module: 5F (Information electronics)
Adaptation → Channel: Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination_over_threshold_high
New value: activated
Procedure ID: 151

Haldex AWD Traction adjustment

Adjust all-wheel-drive system logic to increase traction or reduce noise generated by the mechanism.
Module: 22 (AWD)
Adaptation → Channel: Logic
New value: Standard / Increased Traction / Less Noise
Procedure ID: 68

Headlights Basic Settings procedure (fault C107E)

Perform basic settings procedure to fix "Missing Calibration" error code (C107E) for headlights leveling system.
Car parked against wall to confirm light beam position. Car parked on flat and level surface. No cargo and no passengers in the car. Parking brake engaged. Automatic transmission in P. Ignition on. Headlights on.
Module: 55 (Xenon range)
Basic Settings → Basic headlamp setting → Go
Check if the light beam is projected in correct spot. Adjust manually if needed.
Module: 55 (Xenon range)
Basic Settings → Acknowledge basic setting → Go
Procedure ID: 199

Heated Seats Memory activation

Heated seats will remember last state after switching the ignition, instead of going to off state as default.
Watch Heated Seats Memory activation tutorial on YouTube.
Module: 08 (Automatic heat, ventilation, air condition)
Adaptation → Channel: Retention of the seat heater level driver
New value: active
Module: 08 (Automatic heat, ventilation, air condition)
Adaptation → Channel: Retention of the seat heater level passenger
New value: active
Procedure ID: 30

High Beam Assist and Dynamic Light Assist Memory activation

If your car is equipped with HBA (High Beam Assist) or DLA (Dynamic Light Assist) feature you can adjust the memory option so the feature will remain active after ignition is turned off and back on.
Watch High Beam Assist and Dynamic Light Assist Memory activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Assistance light functions - Fernlichtassistent Reset
New value: not active
Procedure ID: 168

High Beam via Fog Lights activation

Front fog lights will be used as additional high beam lights.
Watch High Beam via Fog Lights activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Lichtfunktion C 12
New value: Left high beam
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Dimmwert CD 12
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Dimming Direction CD 12
New value: Maximize
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Lichtfunktion C 13
New value: Right high beam
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Dimmwert CD 13
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Dimming Direction CD 13
New value: Maximize
Procedure ID: 156

Hill-Hold Release Delay adjustment

Brake will be released faster, with minimum acceleration pedal input.
Module: 03 (ABS brakes)
Security Access → Code: 40168
Module: 03 (ABS brakes)
Adaptation → Channel: Hill-start Assistant
New value: early
Procedure ID: 142

Indicators Comfort Setting adjustment

Adjust count of the comfort indicator setting to increase or decrease number of cycles when short pressing the indicator stalk to change lane.
Watch Indicators Comfort Setting adjustment tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Turn signal control - Komfortblinken Blinkzyklen
New value: 2-5
Procedure ID: 192

Instrument Cluster Display Carbon Background activation

Changes instrument cluster display background image to carbon-fiber style.
Module: 17 (Instruments Cluster)
Adaptation → Channel: Screen View
New value: Option 2
Procedure ID: 28

Instrument Cluster Drive Mode activation

Shows drive profile on instrument cluster when switching between profiles.
Module: 19 (CAN getaway)
Coding → Long Coding → Byte: 08 → Bit: 4
New value: enabled
Procedure ID: 25

Instrument Cluster Key Warning deactivation

Disables warning message that reminds to turn the ignition off and take the key out from the ignition.
Watch Instrument Cluster Key Warning deactivation tutorial on YouTube.
Module: 17 (Instruments Cluster)
Adaptation → Channel: Ignition active message; trigger
New value: no display
Procedure ID: 131

Instrument Cluster Lap Timer activation

Extra trip computer menu with lap timer (optional boost gauge, oil temperature, shift light).
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 01 → Bit: 3
New value: enable
Procedure ID: 1

Instrument Cluster Needle Sweep activation (coding method)

Gauge test when turning the ignition on.
Watch Instrument Cluster Needle Sweep activation (coding method) tutorial on YouTube.
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 01 → Bit: 0
New value: enable
Procedure ID: 2

Instrument Cluster Oil Temperature Display activation

Enables engine oil temperature menu on instrument cluster display.
Watch Instrument Cluster Oil Temperature Display activation tutorial on YouTube.
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 10 → Bit: 1
New value: enable
Procedure ID: 26

Instrument Cluster Rear Fog Light Warning activation

Enables warning message that will remind you about rear fog lights turned on when reachnig set speed.
Watch Instrument Cluster Rear Fog Light Warning activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Driving light and parking light - Nebelschlusslicht Warngeschwindigkeit
New value: 51km/h
Procedure ID: 110

Instrument Cluster Refuel Amount activation

Shows estimated refuel amount on instrument cluster menu.
Watch Instrument Cluster Refuel Amount activation tutorial on YouTube.
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 10 → Bit: 4
New value: enable
Procedure ID: 27

Instrument Cluster Road Sign Recognition activation

Enables option to show current speed limit based on the image recognition function of the front facing camera.
Watch Instrument Cluster Road Sign Recognition activation tutorial on YouTube.
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - traffic sign recognition 0x21
New value: active
Module: 5F (Information electronics)
Adaptation → Channel: Car Function List BAP Gen2 - traffic sign recognition 0x21 msg bus
New value: Databus extended
Module: 5F (Information electronics)
Adaptation → Channel: Car Function Adaptations Gen2 - menu display road sign identification
New value: active
Module: 5F (Information electronics)
Adaptation → Channel: Car Function Adaptations Gen2 - menu display road sign identification over threshold high
New value: active
Module: 5F (Information electronics)
Coding → Long Coding → Byte: 24 → Bit: 6
New value: active
Module: A5 (Front Sensors Driver Assistance System)
Security Access → Code: 20103
Module: A5 (Front Sensors Driver Assistance System)
Coding → Long Coding → Byte: 01 → Bit: 0
New value: active
Module: A5 (Front Sensors Driver Assistance System)
Adaptation → Channel: Road Sign Detection Fusion Mode
New value: Road sign fusion
Module: A5 (Front Sensors Driver Assistance System)
Adaptation → Channel: Display end of speed limit symbol
New value: active
Module: A5 (Front Sensors Driver Assistance System)
Adaptation → Channel: Valid additional characters
New value: 00100111
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 05 → Bit: 2
New value: active
Reboot infotainment unit by pressing and holding volume knob for 10 seconds.
On the infotainment display go to Car → Setup → Driver Assistance Settings → Dynamic Road Sign Display and enable "Show in instrument cluster" option.
On the infotainment display go to Car → Setup → Instrument Cluster Settings and enable "Dynamic Road Sign Display" option.
Procedure ID: 139

Instrument Cluster SAFELOCK! Warning deactivation

Disables "Check SAFELOCK!" warning message from appearing on instruments cluster each time you turn the ignition off.
Watch Instrument Cluster SAFELOCK! Warning deactivation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 08 → Bit: 6
New value: enable
Module: 09 (Central Electronics)
Adaptation → Channel: ZV allgemein - ZV_ohne_Safe_Funktion
New value: installed
Procedure ID: 178

Instrument Cluster Seat Belt Reminder deactivation

Disables seat belt warning indicator and warning sound.
Watch Instrument Cluster Seat Belt Reminder deactivation tutorial on YouTube.
Module: 17 (Instruments Cluster)
Adaptation → Channel: Disable seat belt warning
New value: Yes
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 00 → Bit: 2-4
New value: disable
Seat belt is a safety device designed to secure the occupant of a vehicle against harmful movement that may result during a collision or a sudden stop. Please always wear seat belt.
Procedure ID: 29

Interior Lights Fade-out activation

Enables interior lights to softly fade out when shutting off.
Watch Interior Lights Fade-out activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Interior lighting-KL58 Einschalten mit Rampe
New value: active
Procedure ID: 129

LED Fog Lights adjustment

Change fog lights configuration to LED to prevent broken bulb warning message and adjust PWM signal for full brightness.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Leuchte12NL Lasttyp-12
New value: 6-LED Lichtmodule
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte12NL LB45-Dimmwert AB 12
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Leuchte12NL Lasttyp-13
New value: 6-LED Lichtmodule
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte13NL RB5-Dimmwert AB 13
New value: 127
Procedure ID: 125

LED License Plate Light adjustment

Disables cold check for bulbs installed above license plate, sets the control unit to LED mode, adjusts PWM signal for full brightness.
Get VAG LED license plate lamp on Ali4Cars.com
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte25KZL HA59 – Lasttyp 25
New value: Allgemeine LED
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte25KZL HA59 – Dimmwert AB 25
New value: 127
Procedure ID: 127

LED Rear Turn Signals adjustment

Change rear turn signal lights configuration to LED to prevent broken bulb warning message and adjust PWM signal for full brightness.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte18BLK HLA60 – Lasttyp 18
New value: Allgemeine LED
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte18BLK HLA60 – Dimmwert AB 18
New value: 127
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte19BLK HRC31 – Lasttyp 19
New value: Allgemeine LED
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte19BLK HRC31 – Dimmwert AB 19
New value: 127
Procedure ID: 141

LED Reverse Lights adjustment

Change reverse lights configuration to LED to prevent broken bulb warning message.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte28RFL-Lasttyp 28
New value: 43 - allgemeine LED
Module: 09 (Central Electronics)
Adaptation → Channel: Leuchte29RFL-Lasttyp 29
New value: 43 - allgemeine LED
Procedure ID: 190

Parktronic Visualization (OPS) without Camera activation

Display obstacles data from parking sensors on the main unit display.
Module: 10 (Parking/steering assist)
Security Access → Code: 71679
Module: 10 (Parking/steering assist)
Coding → Long Coding → Byte: 02 → Bit: 0
New value: enable
Procedure ID: 37

Parktronic Warning Message deactivation

Removes "Please check surroundings" warning message on the display when engaging reverse gear.
Module: 03 (ABS brakes)
Security Access → Code: 71679
Module: 03 (ABS brakes)
Coding → Long Coding → Byte: 01 → Bit: 5
New value: disable
Procedure ID: 71

Parktronic Warning Tone deactivation

Disables warning tone from rear speakers when engaging reverse gear.
Module: 03 (ABS brakes)
Adaptation → Channel: Park Assist Activation Tone
New value: off
Procedure ID: 138

Personalisation Profiles activation

Enables 3 custom driver profiles and guest account with separate personal settings. Profiles can be switched from the instrument cluster and the infotainment screen.
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 08 → Bit: 2
New value: enable
Module: 09 (Central Electronics)
Coding → Long Coding → Byte: 11 → Bit: 4
New value: enable
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - peronalisierung_active
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - aktivierungsoption_im_HMI-menue_sichtbar
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - Benutzerkontenverwaltung_in_HMI-menue_sichtbar
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - Personalisierungfunktionen_in_HMI-menue_sichtbar
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - Anzahl_Benutzenkontante
New value: 4
Module: 09 (Central Electronics)
Adaptation → Channel: Personalisierung - Automatische_Schluesselzuordnung
New value: active
Module: 08 (Automatic heat, ventilation, air condition)
Coding → Long Coding → Byte: 15 → Bit: 3
New value: enable
Module: 17 (Instruments Cluster)
Coding → Long Coding → Byte: 10 → Bit: 0
New value: enable
Reboot infotainment unit by pressing and holding volume knob for 10 seconds.
Procedure ID: 150

Rear Wiper Tear Wipe activation

Enables additional rear wiper move after using windscreen washer.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Rear Window Wiper-Heckwischer Weiterlauf
New value: active
Procedure ID: 123

Remote Keyless Windows Control activation

Put and keep your hand on the door handle to open and close windows.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Kessy Komfort oeffnen
New value: not active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Kessy Komfort schliessen
New value: active
Procedure ID: 147

Remote Sunroof Control activation

Long-press remote buttons to open and close sunroof.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - SAD Komfort schliessen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - SAD Komfort oeffnen
New value: active
Procedure ID: 145

Remote Sunroof Control adjustment

Change your sunroof to tilt when long-pressing remote buttons to open it.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - SAD Richtung Komfortoeffnen
New value: tilting
Procedure ID: 146

Remote Windows Control activation

Long-press remote buttons to open and close windows.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Comfort closing
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Comfort opening
New value: not active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Komfort schliessen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Komfort oeffnen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Menuesteuerung Komfortbedienung einstellbar
New value: adjustable
Procedure ID: 144

Remote with Ignition On activation

Enables the remote buttons to work with the ignition turned on.
Watch Remote with Ignition On activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access control - Funk bei Klemm 15 ein
New value: active
Procedure ID: 132

START/STOP System deactivation (gateway coding method)

START/STOP system will no longer work by removing this feature from gateway coding.
Get VW Engine Start-Stop memory module on Ali4Cars.com
Module: 19 (CAN getaway)
Coding → Long Coding → Byte: 03 → Bit: 2
New value: disabled
Module: 19 (CAN getaway)
Coding → Long Coding → Byte: 03 → Bit: 3
New value: enabled
Module: 19 (CAN getaway)
Coding → Long Coding → Byte: 04 → Bit: 0
New value: disabled
Module: 19 (CAN getaway)
Coding → Long Coding → Byte: 15 → Bit: 0
New value: disabled
Procedure ID: 160

START/STOP System deactivation (prohibition method)

START/STOP system will no longer work by blocking engine stop feature.
Get VW Engine Start-Stop memory module on Ali4Cars.com
Module: 19 (CAN getaway)
Adaptation → Channel: Deactivation of start-stop function
New value: Stop prohibition: no start request
Procedure ID: 161

START/STOP System deactivation (temperature method)

START/STOP system will no longer work by changing the temperature limits.
Watch START/STOP System deactivation (temperature method) tutorial on YouTube.
Get VW Engine Start-Stop memory module on Ali4Cars.com
Module: 19 (CAN getaway)
Adaptation → Channel: Start/Stopp AußentemperaturVorgabe-MaximaleTemperatur
New value: 50
Module: 19 (CAN getaway)
Adaptation → Channel: Start/Stopp AußentemperaturVorgabe-MinimaleTemperatur
New value: 50
Procedure ID: 134

START/STOP System deactivation (voltage method)

START/STOP system will no longer work by increasing the low voltage limit.
Watch START/STOP System deactivation (voltage method) tutorial on YouTube.
Get VW Engine Start-Stop memory module on Ali4Cars.com
Module: 19 (CAN getaway)
Adaptation → Channel: Start_stop_voltage_limit
New value: 12
Procedure ID: 133

Side Mirror Tilt on Reverse activation

Passengers mirror will tilt down when in reverse and control switch set to passengers side. Function can also be controlled from main unit screen.
Watch Side Mirror Tilt on Reverse activation tutorial on YouTube.
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 04 → Bit: 2
New value: enable
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 04 → Bit: 3
New value: enable
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Spiegelabsenkung bei Rueckwaertsfahrt
New value: Active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Menuesteuerung Spiegelabsenkung
New value: Active
Procedure ID: 35

Side Mirrors Entry Lights On when Mirrors Folded activation

Activate entry lights to stay on with side mirrors folded.
Watch Side Mirrors Entry Lights On when Mirrors Folded activation tutorial on YouTube.
Module: 42 (Driver door electronics)
Coding → Long Coding → Byte: 01 → Bit: 5
New value: disable
Module: 52 (Passenger door electronics)
Coding → Long Coding → Byte: 01 → Bit: 5
New value: disable
Procedure ID: 120

Side Mirrors Fold with Central Lock activation

Enable mirrors folding when locking the car by remote control.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Spiegelanklappen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Menuesteuerung Funkspiegelanklappen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Spiegelanklappung Modus
New value: by look command via remote control key
On the infotainment display go to Car → Setup → Mirrors & Wipers and enable "Fold away after parking" option.
Procedure ID: 119

Side Mirrors Fold with Comfort Closing activation

Enable mirrors fold function to work when using comfort closing feature. Instead of folding each time the car is locked, mirrors will fold after press and hold of the lock button on the remote control.
Watch Side Mirrors Fold with Comfort Closing activation tutorial on YouTube.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Spiegelanklappen
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Access Control 2 - Funk Spiegelanklappung Modus
New value: by convenience operation of the remote control key
Procedure ID: 152

Soundaktor deactivation

Disables fake engine sound generated by soundaktor module.
Module: A9 (Structure Borne Sound)
Adaptation → Channel: Volume of structure borne noise actuator
New value: 0%
Procedure ID: 24

Starting Torque Limitation deactivation

Disables torque limiter function for starting vibration reduction.
Module: 03 (ABS brakes)
Adaptation → Channel: Starting Vibration Reduction and Torque Limitation
New value: Deactivated
Procedure ID: 31

Welcome Lights with Reverse Gear activation

Welcome lights under side mirrors will turn on when reverse gear is selected.
Module: 6C (Rear view camera)
Coding → Long Coding → Byte: 08 → Bit: 2
New value: enable
Module: 09 (Central Electronics)
Security Access → Code: 31347
Adaptation → Channel: Aussenlicht_uebergreifend - Umfeldleuchte als Manoevrierleuchte
New value: enable
Procedure ID: 165

Windscreen Wipers Tear Wipe activation

Additional wiper move after using windscreen washer.
Module: 09 (Central Electronics)
Security Access → Code: 31347
Module: 09 (Central Electronics)
Adaptation → Channel: Windshield wiper-Traenenwischen Front Status
New value: active
Module: 09 (Central Electronics)
Adaptation → Channel: Windshield wiper-Menuesteuerung Frontwischer
New value: active
Procedure ID: 122

XDS Differential Lock adjustment

Adjust electronic differential locker for better grip when cornering. Improve responses when fast cornering by the XDS lightly braking the inside wheel to prevent wheel spinning.
Module: 03 (ABS brakes)
Adaptation → Channel: Expanded Electronic Differential Lock
New value: Weak / Normal / Hard
Procedure ID: 69