Mods, retrofits, service procedures:

• Central Lock Blink activation

  Enables confirmation with blinkers when lockind and unlocking the car.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 05 → Bit: 0
  New value: enable

  Procedure ID: 85

• Central Lock Honk when Locking activation

  Enables honk confirmation when locking the car.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 05 → Bit: 1
  New value: enable

  Procedure ID: 86

• Central Lock Honk when Unlocking activation

  Enables honk confirmation when unlocking the car.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 05 → Bit: 4
  New value: enable

  Procedure ID: 87

• Comfort Turn Signals Count adjustment

  Changes how many times should the indicator blink when using comfort indicators.

  Module: 09 (Central Electronics)
  Adaptation → Channel: 31
  New value: newValue

  New value within range from 1 to 5.

  Procedure ID: 89

• Coming Home lights via Fog Lights activation

  Front fog lights will be used as coming home lights.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 17 → Bit: 3
  New value: enable

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 17 → Bit: 5
  New value: enable

  Procedure ID: 92

• Cornering Lights via Fog Lights activation

  Front fog lights will be used as cornering lights.

  Watch Cornering Lights via Fog Lights activation tutorial on YouTube.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 14 → Bit: 7
  New value: enable

  Procedure ID: 90

• DRLs via Fog Lights activation

  Front fog lights will be used as daytime running lights.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 14 → Bit: 1
  New value: enable

  Procedure ID: 91

• Emergency Brake Lights activation

  Flashing brake lights when emergency braking and hazard lights when emergency stopping.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 16 → Bit: 1
  New value: enable

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 16 → Bit: 2
  New value: enable

  Procedure ID: 88

• Instrument Cluster Needle Sweep activation (adaptation method)

  Gauge test when turning the ignition on.

  Module: 17 (Instruments Cluster)
  Adaptation → Channel: Indicator Celebration
  New value: enable

  Procedure ID: 76

• Instrument Cluster Refuel Amount activation

  Shows estimated refuel amount on instrument cluster menu.

  Module: 17 (Instruments Cluster)
  Adaptation → Channel: Volume to be Replenished
  New value: yes

  Procedure ID: 77

• LED Footwell Lights adjustment

  Disables cold checking for bulbs installed above footwells.

  Use this if replacing regular bulbs with LEDs without CAN-BUS resistor.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 25 → Bit: 3
  New value: disable

  Procedure ID: 93

• LED License Plate adjustment

  Disables cold checking bulbs installed above license plate.

  Use this if replacing regular bulbs with LEDs without CAN-BUS resistor.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 23 → Bit: 6
  New value: disable

  Procedure ID: 94

• Rain Sensor Comfort Closing activation

  Enables automatic closing of windows and sunroof when rain sensor detects water.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 04 → Bit: 6
  New value: enable

  Procedure ID: 78

• Rear Wiper Automatic in Reverse activation

  Enables rear wiper when reverse gear is engaged and front wipers are on.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 21 → Bit: 6
  New value: enable

  Procedure ID: 79

• Rear Wiper Automatic with Front Wipers in Interval activation

  Enables rear wiper whenever front wipers are set to time interval operation.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 21 → Bit: 2
  New value: enable

  Procedure ID: 80

• Rear Wiper Automatic with Front Wipers in Permanent activation

  Enables rear wiper whenever front wipers are set to permanent operation.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 21 → Bit: 3
  New value: enable

  Procedure ID: 81

• Rear Wiper Tear Wipe activation

  Enables additional rear wiper move after using windscreen washer.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 21 → Bit: 4
  New value: enable

  Procedure ID: 82

• Side Mirror Tilt on Reverse activation

  Passengers mirror will tilt down when in reverse and control switch set to passengers side. Function can also be controlled from main unit screen.

  Mirror adjustment switch must be set to passengers door for mirror dip to be active.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 04 → Bit: 3
  New value: enable

  Procedure ID: 83

• Side Mirrors Fold with Remote activation

  Press and hold close button on the remote control to fold side mirrors.

  Module: 42 (Driver door electronics)
  Coding → Long Coding → Byte: 00 → Bit: 4
  New value: enable

  Module: 42 (Driver door electronics)
  Coding → Long Coding → Byte: 00 → Bit: 5
  New value: enable

  Module: 52 (Passenger door electronics)
  Coding → Long Coding → Byte: 00 → Bit: 4
  New value: enable

  Module: 52 (Passenger door electronics)
  Coding → Long Coding → Byte: 00 → Bit: 5
  New value: enable

  Module: 42 (Driver door electronics)
  Security Access → Code: 04354
  Adaptation → Channel: System_Parameter_0 (Byte 08)
  New value: newValue

  Set newValue to:
  95 to retract mirrors with ignition on
  99 to retract mirrors with door open.

  Procedure ID: 103

• Side Mirrors Synchronization activation

  Enables adjusting both side mirrors at the same time.

  Module: 09 (Central Electronics)
  Coding → Long Coding → Byte: 08 → Bit: 6
  New value: enable

  Procedure ID: 84